COMPANY HEADER
Request Information
  • Made from FEP fluoropolymer tubing
  • Corrugations allow a nearly zero bend radius - easily flexed
  • Can be extended or compressed without affecting the tube's I.D.
  • Made without plasticizers which can leach into critical streams
  • Made from FDA compliant materials
  • Has all the chemical and electrical properties of straight-walled FEP tubing
  • May be over braided with Kevlar® for higher pressures (Over braiding with Kevlar will permit a minimum increase of six times the listed pressures. Kevlar® over braiding is available for sizes up to 7/8" I.D. - call for details.)
Unit of Measure

Specifications

Brands

 N/A Corrtef™ NewAge

Material

 N/A Fluorinated Ethylene Propylene (FEP)
Maximum Inner Diameter (ID) A1 N/A 5/8 in
Nominal Cuff Length B2 N/A 1 in

Nominal Wall Thickness C

 N/A 0.025 in

Corrugation Outer Diameter (OD) D

 N/A 15/16 in

Working Pressure at 72 Degree Fahrenheit (ºF) Temperature

 N/A 37 psi

Burst Pressure at 72 Degree Fahrenheit (ºF) Temperature

 N/A 148 psi

Vacuum Service at 72 Degree Fahrenheit (ºF) Temperature

 N/A 29.9 inHg

Tubing Bend Inner Diameter (ID) at 72 Degree Fahrenheit (ºF) Temperature

 N/A 1/2 in

Custom Services

 N/A And More Cut Overbraid Size

Industry Standards

 N/A Food and Drug Administration (FDA) Compliant

Physical Properties

Shore Hardness

 N/A 55 to 60 duro

Tensile Strength

 N/A 2800 to 5000 psi

Elongation at Break

 N/A 250 to 330 %

Brittle Temperature

 N/A -450 ºF

Minimum Operating Temperature for Tubing

 N/A -100 ºF

Maximum Operating Temperature for Tubing

 N/A 200 ºF

Note for Operating Temperature

 N/A Temperatures are for standard extruded (non corrugated) tubing.

Note for Physical Properties

 N/A Values listed are typical for the material used in manufacture, except where noted, and are meant only as a guide to aid in design. Field testing should be performed to find the actual values for your application.

Recommended Fittings and Clamps

Recommended Fittings and Clamps

 N/A
  • Thermobarb® barbed fittings
  • Oetiker® ear type clamps
  • Kwik Clamp™ nylon double bond hose clamps
  • Worm gear clamps

Note

Note

 N/A Made in U.S.A.



Optimal flow is achieved and turbulence minimized by passing fluids through Corrtef™ in the direction of the corrugation angles (as illustrated).

Corrtef™ is heat sealable, and the cuffs (straight ends) are made to accept standard barbed fittings. The end may be flared or expanded to permit shrink-tight connections.

Corrtef™ is manufactured in an industrial atmosphere and should be properly sterilized for clean-flow applications. For optimal cleaning of Corrtef™, the tube should be stretched to its maximum length and held vertically (direction of flow: down). Due to the annular corrugations, it may not be possible to remove all traces of particulate from Corrtef™, even under optimal cleaning conditions.

Specify 'E' dimension at order time. Maximum overall available length: 12 ft. (including cuffs). The minimum overall length for Corrtef with a cuff at each end is 6"; shorter overall lengths are possible when only one cuff is needed.

All pressures are calculated and not based on actual testing.
  • 1 Critical dimension for fittings application.
  • 2 Workable I.D. length of the cuff (straight ends). All lengths supplied with 'B' dimension cuffs.